The Autonerdz Community Forums

	Welcome, Guest. Please Login or Register

Home

Help

Member Map

Event Calendar

The Autonerdz Community Forums › › › labour times

‹ Previous Topic | No Topic ›

Pages: 1

Send Topic

labour times (Read 233 times)

sneaky pete Super Nerd Picogroup Offline Posts: 730 Regina Saskatchewan Canada	labour times Jul 8^th, 2014 at 9:44am hope this is appropriate for this forum. I have a 2004 Maserati coupe/spyder and need labour times if anyone could help. vin is zambc38a640012363 labour time for right front wheel bearing and also upper ball joint. not sure if ball joint is replaceable or control arm. thanks sneaky
Back to top	IP Logged

Spence LSD Guide Picogroup Offline Posts: 8,025 Jeffersonville Pennsylvania USA Gender:	Re: labour times Reply #1 - Jul 8^th, 2014 at 6:12pm I would charge what you feel this job should cost for you to make a profit. I looked but no listing in my info system.
Back to top	N.B.S. Dilly Dilly! FJB WWW IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,598 Olympia Washington USA Gender:	Re: labour times Reply #2 - Jul 8^th, 2014 at 7:26pm A Maserati owner should know that, if you have to ask, you can't afford it.
Back to top	Tom Roberts Forums Administrator IP Logged

Spence LSD Guide Picogroup Offline Posts: 8,025 Jeffersonville Pennsylvania USA Gender:	Re: labour times Reply #3 - Jul 8^th, 2014 at 7:29pm Tom Roberts wrote on Jul 8^th, 2014 at 7:26pm: A Maserati owner should know that, if you have to ask, you can't afford it. That was my 1st thought too.
Back to top	N.B.S. Dilly Dilly! FJB WWW IP Logged

Ward Zintel

Super Nerd
Picogroup

Offline

Posts: 632

Saskatoon
Saskatchewan
Canada
Gender: male

Re: labour times
Reply #4 - Jul 9^th, 2014 at 5:03am

Good morning Sneaky!
I had no idea there was a Maserati in Saskatchewan!
Has it got Sk. plates on it or is it someone driving through?
We have Mitchell here, they have jack sh^t for information on that car. Can you call or email your service info provider and get them to supply?
Best of luck. If it's a neat car grab some photos. Heck, if it's some local who lucked onto a Maserati and is trying to operate and maintain it on a Pinto budget get some photos of that also! Always wondered how well the high end stuff lended itself to duct tape and baler twine repairs.
-Ward-

Wayne's Driveline
Saskatoon, Sk.

IP Logged

sneaky pete

Super Nerd
Picogroup

Offline

Posts: 730

Regina
Saskatchewan
Canada

Re: labour times
Reply #5 - Jul 9^th, 2014 at 7:55am

yes I agree with you all. I will probably go ahead and make up a quote off my gut feeling. was hoping to get labour times and torque specs from one of the service providers but nothing. I tried Mitchell, alldata, motologic and identifix. nothing for Maserati's. I contacted some and they said they had no info at all.

ward, yes apparently this is the only Maserati in Sask. hahaha. I was quite surprised when it rolled in. the owner is here in regina. has lots of money apparently...

thanks for the replies. much appreciated.

IP Logged

Dave R Freshman Member Picogroup Offline I'm an Autonerd Posts: 2 Winnipeg Manitoba Canada Gender:	Re: labour times Reply #6 - Jul 18^th, 2014 at 8:18pm A fellow Canadian in Manitoba would say a Meserati a never got payed for was either a rich Asian or E Indian who all ready has more money than God and is just a cheap n out fucker
Back to top	IP Logged

Pages: 1

Send Topic

‹ Previous Topic | No Topic ›

« Home

‹ Board

Top of this page

Autonerdz forums