The Autonerdz Community Forums

PicoFin

Guru Member

Offline

Posts: 276

Parainen
Finland
Gender: male

WPS 500 x
Mar 18^th, 2013 at 1:10am

Hi there

Two questions came to mind, while using the WPS after reading the user manual, and I'd rather ask the field than Pico:

-how essential have you found to dismantle the bleeding screw for flushing the unit after each use? i understand you would like to do that if you had engine oil in it, but exhaust, petrol, diesel or air can't be bad, right?

-has anyone yet managed to destroy their WPS accidentally by applying too much pressure? I know it runs out of scale above 500 psi so you can't see on the screen how much there was, but if you destroyed yours (or didn't), with what pressure? Just curious..

Back to top

IP Logged

Mick

LSD Guide

Offline

I learn every day

Posts: 7,471

Toronto 400ft
Ontario
Canada
Gender: male

Re: WPS 500 x
Reply #1 - Mar 18^th, 2013 at 6:15am

PicoFin wrote on Mar 18^th, 2013 at 1:10am:

-how essential have you found to dismantle the bleeding screw for flushing the unit after each use?

I did it once because I read the manual and never did it again but I will say if I use it on the fuel rail or coolant I will leave it open and hang the unit straight for a couple of hours to dry out.

PicoFin wrote on Mar 18^th, 2013 at 1:10am:

-has anyone yet managed to destroy their WPS accidentally by applying too much pressure?

Never had to use it on such high pressure maybe because I don't work on diesel's Undecided

If the charge runs out don't use it whilst charging just plug the USB cable into a PC and leave it until the lights go out.

Back to top

Mick

IP Logged

daveyK

Super Nerd
Picogroup

Offline

(Retired) - Elevation:
525 feet

Posts: 2,357

Hellertown, PA, USA
Pennsylvania
USA
Gender: male

Re: WPS 500 x
Reply #2 - Mar 18^th, 2013 at 7:28am

Hello PicoFin,

Like Mick I leave my bleed screw open to drain and also because I put a quick connect with a check valve in it. I leave the bleed valve open to calibrate so it is accurate to atmosphere.

I used my WPS ONE time on a power steering pump where the psi spiked to over 500.

I would not recommend constant use at these pressures even though there is a built in safety factor to protect unit failure Wink

HTH

Back to top

IP Logged

autosparky

Super Nerd
Picogroup

Offline

blind worker

Posts: 2,537

Porirua
New Zealand
Gender: male

Re: WPS 500 x
Reply #3 - Mar 19^th, 2013 at 10:02pm

PicoFin wrote on Mar 18^th, 2013 at 1:10am:

how essential have you found to dismantle the bleeding screw for flushing the unit after each use?

WHAT??? I never that part in the manual and I've had mine for 2 years now.
I used it today on a fuel system but I always shake all the fluid out.

Actually what I did with my fuel pressure reading was hook my multi meter to it for a quick test, I'm just too lazy to boot up my laptop Roll Eyes

I haven't bashed my unit around too much but not really happy about the steel case design, it just knocks against everything in the engine bay

Back to top

can't see, can't hear, can't remember

IP Logged

Eddie Senior Member Offline Posts: 220 Auckland New Zealand Gender:	Re: WPS 500 x Reply #4 - Mar 19^th, 2013 at 10:19pm autosparky wrote on Mar 19^th, 2013 at 10:02pm: not really happy about the steel case design, it just knocks against everything in the engine bay Perhaps then that makes a case (excuse the pun) for an Autonerdz rubberized protective case to help protect it & vehicle?
Back to top	Eddie A Grade Mechanical Services Sydney IP Logged

PicoFin Guru Member Offline Posts: 276 Parainen Finland Gender:	Re: WPS 500 x Reply #5 - Mar 20^th, 2013 at 4:06am Exactly what came to mind for me too. Protective rubber case for the WPS, we want! EDIT: actually the idea was so damn good, I emailed it to Pico right away! Let's sit back and wait, and see what happens..?
Back to top	IP Logged

BMW Scott Super Nerd Picogroup Offline Posts: 561 High Point, NC North Carolina USA Gender:	Re: WPS 500 x Reply #6 - Mar 23^rd, 2013 at 5:18pm PicoFin wrote on Mar 20^th, 2013 at 4:06am: Protective rubber case for the WPS, we want! x3
Back to top	Scott J Hicks IP Logged

Spence LSD Guide Picogroup Offline Posts: 8,025 Jeffersonville Pennsylvania USA Gender:	Re: WPS 500 x Reply #7 - Mar 24^th, 2013 at 4:30am BMW Scott wrote on Mar 23^rd, 2013 at 5:18pm: PicoFin wrote on Mar 20^th, 2013 at 4:06am: Protective rubber case for the WPS, we want! x3 +4
Back to top	N.B.S. Dilly Dilly! FJB WWW IP Logged

PicoFin Guru Member Offline Posts: 276 Parainen Finland Gender:	Re: WPS 500 x Reply #8 - Mar 24^th, 2013 at 9:28pm The answer was that the idea will get forwarded, but first feel is that since the amount of WPS's sold is not by far the same that the number of sold scopes are, it might get too expensive to manufacture due to the small amounts? We'll see..
Back to top	IP Logged

autosparky Super Nerd Picogroup Offline blind worker Posts: 2,537 Porirua New Zealand Gender:	Re: WPS 500 x Reply #9 - Mar 26^th, 2013 at 11:00pm Bet someone in China can make 500 for $1.00 each
Back to top	can't see, can't hear, can't remember IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #10 - Apr 4^th, 2013 at 2:56pm Just so you know we're paying attention... Still working things out, but we hope to have these soon.
Back to top	WPS_bumpers.jpg (329 KB \| ) Brian Haley Autonerdz.com IP Logged

KarlW

LSD Guide
Picogroup

Offline

Picoscope In The Ville

Posts: 1,347

Somerville
Massachusetts
USA
Gender: male

Re: WPS 500 x
Reply #11 - Apr 4^th, 2013 at 3:03pm

Brian Haley wrote on Apr 4^th, 2013 at 2:56pm:

Just so you know we're paying attention...Still working things out, but we hope to have these soon.

Hi Brian,

Thats really cool! did you guys make them? Also are the WPS's still available with turnable Purge valve instead of push style? If so do you have to specify when you order them?

Thanks
Karl

Back to top

IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #12 - Apr 4^th, 2013 at 3:09pm Hi Karl, These might work with the turn style relief valves, but I don’t have one here to test fit. The WPS is no longer made with the turn style valve.
Back to top	Brian Haley Autonerdz.com IP Logged

daveyK Super Nerd Picogroup Offline (Retired) - Elevation: 525 feet Posts: 2,357 Hellertown, PA, USA Pennsylvania USA Gender:	Re: WPS 500 x Reply #13 - Apr 4^th, 2013 at 3:10pm Hello Brian, Do you have any specs? The buttons sure do look like the WPS Thanks
Back to top	IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #14 - Apr 4^th, 2013 at 3:12pm daveyK wrote on Apr 4^th, 2013 at 3:10pm: The buttons sure do look like the WPS It is a WPS500, just has bumpers attached to each end
Back to top	Brian Haley Autonerdz.com IP Logged

Spence LSD Guide Picogroup Offline Posts: 8,025 Jeffersonville Pennsylvania USA Gender:	Re: WPS 500 x Reply #15 - Apr 4^th, 2013 at 3:13pm Brian Haley wrote on Apr 4^th, 2013 at 3:09pm: Hi Karl, These might work with the turn style relief valves, but I don’t have one here to test fit. I do if you want to send one my way.
Back to top	N.B.S. Dilly Dilly! FJB WWW IP Logged

daveyK Super Nerd Picogroup Offline (Retired) - Elevation: 525 feet Posts: 2,357 Hellertown, PA, USA Pennsylvania USA Gender:	Re: WPS 500 x Reply #16 - Apr 4^th, 2013 at 3:38pm Brian, Will the rubber baby bumpers fit the older WPS? Thanks
Back to top	IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #17 - Apr 5^th, 2013 at 7:03am daveyK wrote on Apr 4^th, 2013 at 3:38pm: Will the rubber baby bumpers fit the older WPS? The pressure release is the only change that has been made to the WPS units. Early units had the turn knob, now they have a button.
Back to top	Brian Haley Autonerdz.com IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #18 - Apr 5^th, 2013 at 7:42am Also, the WPS won't fit in its carry case with these on. The foam would need some trimming.
Back to top	« Last Edit: Apr 5^th, 2013 at 8:18am by Brian Haley » Brian Haley Autonerdz.com IP Logged

BMW Scott

Super Nerd
Picogroup

Offline

Posts: 561

High Point, NC
North Carolina
USA
Gender: male

WPS500 Protective Bumpers
Reply #19 - Apr 13^th, 2013 at 12:10pm

My protective bumpers for my WPS500 arrived this week and I thought I would share a few pictures and thoughts.

They seem to be made of pretty good rubber that would absorb most drops. Even though they are two separate pieces, they stay on very well so far. The top one has a cutout for the power button and the bottom one has a cutout on the side for the release valve, but the cutout is a little off. I plan on trimming it a little more to fit around the release button a little better. Overall I think its a great idea and am glad to have them. Any protection I can have to protect my investment is always appreciated.

Thanks Tom and Brian!

Back to top

wps500_bumpers_1.jpg (122 KB | )

wps500_bumpers_2.jpg (72 KB | )

wps500_bumpers_3.jpg (140 KB | )

wps500_bumpers_4.jpg (129 KB | )

Scott J Hicks

IP Logged

BMW Scott

Super Nerd
Picogroup

Offline

Posts: 561

High Point, NC
North Carolina
USA
Gender: male

Re: WPS500 Protective Bumpers
Reply #20 - Apr 13^th, 2013 at 1:00pm

Oh and I almost forgot. The top bumper covers the usb charging port, which at first, I wasn't sure if I liked that or not. But after thinking about it for awhile, I've decided that I am happy about it covering the charging port. It keeps dust and dirt out of the port and bumper easily slides up enough to charge it. And besides, I don't know how well it would stay on if it had a cutout for the charging port.

Back to top

wps500_bumpers_5.jpg (103 KB | )

Scott J Hicks

IP Logged

big4x42u Freshman Member Picogroup Offline I'm an Autonerd Posts: 16 Santa Maria California USA Gender:	Re: WPS500 Protective Bumpers Reply #21 - Apr 13^th, 2013 at 5:45pm When will the protective boots be readily available to purchase?
Back to top	IP Logged

BMW Scott Super Nerd Picogroup Offline Posts: 561 High Point, NC North Carolina USA Gender:	Re: WPS500 Protective Bumpers Reply #22 - Apr 13^th, 2013 at 6:04pm big4x42u wrote on Apr 13^th, 2013 at 5:45pm: When will the protective boots be readily available to purchase? That's gonna be a question for Tom or Brian, which I'm sure they will see tomorrow or Monday.
Back to top	Scott J Hicks IP Logged

Brian Haley

Autonerdz Administrator
Picogroup

Offline

Posts: 570

White Pass, WA
Washington
USA
Gender: male

Re: WPS 500 x
Reply #23 - Apr 15^th, 2013 at 7:59am

Thanks for the write-up Scott,

Your prototype didn’t have the button hole placed quite right; we've improved the placement to minimize spreading of the bumper in that area.

We felt the same about leaving the charging port covered.

We are hoping to have a batch ready to go this week, $10.00 + $5.00 to ship in a USPS priority flat rate box within the U.S. Priority boxes usually arrive in 2-3 days and we haven’t lost one yet.

Back to top

Brian Haley
Autonerdz.com

IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,598 Olympia Washington USA Gender:	Re: WPS 500 x Reply #24 - Apr 15^th, 2013 at 8:04am We also poured gasoline on a sample bumper to see what would happen. They held up just fine...just made them a bit stinky.
Back to top	Tom Roberts Forums Administrator IP Logged

Spence LSD Guide Picogroup Offline Posts: 8,025 Jeffersonville Pennsylvania USA Gender:	Re: WPS 500 x Reply #25 - Apr 15^th, 2013 at 8:26am Mine came in over the weekend. Fit is good. I will post pictures later.
Back to top	N.B.S. Dilly Dilly! FJB WWW IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #26 - Apr 15^th, 2013 at 1:19pm We have them up sooner than we thought. http://www.autonerdz.com/wps500.html#wps500boot
Back to top	Brian Haley Autonerdz.com IP Logged

BMW Scott

Super Nerd
Picogroup

Offline

Posts: 561

High Point, NC
North Carolina
USA
Gender: male

Re: WPS 500 x
Reply #27 - Apr 15^th, 2013 at 5:24pm

Brian Haley wrote on Apr 15^th, 2013 at 7:59am:

Thanks for the write-up Scott,

Your prototype didn’t have the button hole placed quite right; we've improved the placement to minimize spreading of the bumper in that area.

We felt the same about leaving the charging port covered.

Thanks again for the prototype! I'm definitely not complaining about the button hole. Nothing a little exacto knife can't fix. Smiley

Back to top

Scott J Hicks

IP Logged

Spence LSD Guide Picogroup Offline Posts: 8,025 Jeffersonville Pennsylvania USA Gender:	Re: WPS 500 x Reply #28 - Apr 15^th, 2013 at 5:56pm Here's how mine looked with the new bumpers. Mine has the turn style release valve. The bumper for this end slide right under it with clearance to spare. Thanks Spence
Back to top	« Last Edit: Apr 15^th, 2013 at 6:11pm by Spence » IMG_2602.jpg (548 KB \| ) IMG_2607.jpg (594 KB \| ) IMG_2608.jpg (459 KB \| ) IMG_2604.jpg (441 KB \| ) IMG_2606.jpg (443 KB \| ) N.B.S. Dilly Dilly! FJB WWW IP Logged

Eddie Senior Member Offline Posts: 220 Auckland New Zealand Gender:	Re: WPS 500 x Reply #29 - Apr 16^th, 2013 at 3:10am Well that would have to be one of the quickest responses to a customer idea/request I ever did see !! Maybe it just needs a little Autonerdz branding stylised into it to finish it up huh Well done Tom & co
Back to top	Eddie A Grade Mechanical Services Sydney IP Logged

BMW Scott Super Nerd Picogroup Offline Posts: 561 High Point, NC North Carolina USA Gender:	Re: WPS 500 x Reply #30 - Apr 16^th, 2013 at 3:34am Eddie wrote on Apr 16^th, 2013 at 3:10am: Maybe it just needs a little Autonerdz branding stylised into it to finish it up huh I would be okay if it said Autonerdz on it somewhere.
Back to top	Scott J Hicks IP Logged

Robski Guru Member Picogroup Offline Posts: 262 Yorkshire Great Britain Gender:	Re: WPS 500 x Reply #31 - Apr 16^th, 2013 at 11:16am Tom/Brian What's the UK shipping price on these please ?
Back to top	Cheers Rob. IP Logged

Brian Haley Autonerdz Administrator Picogroup Offline Posts: 570 White Pass, WA Washington USA Gender:	Re: WPS 500 x Reply #32 - Apr 16^th, 2013 at 12:27pm One set including shipping to the UK would be $34.00. We can't insure the small USPS boxes, so a bit of a risk for the purchaser. We haven’t lost one yet though.
Back to top	Brian Haley Autonerdz.com IP Logged

Robski Guru Member Picogroup Offline Posts: 262 Yorkshire Great Britain Gender:	Re: WPS 500 x Reply #33 - Apr 16^th, 2013 at 12:56pm thanks for the reply Brian, i PM'd Tom earlier as i would want 2X sets shipping to the UK, you can answer that if you wish. I will then have to sort out the payment etc tomorrow some time. EDIT: Tom has replied thanks.
Back to top	Cheers Rob. IP Logged

autosparky Super Nerd Picogroup Offline blind worker Posts: 2,537 Porirua New Zealand Gender:	Re: WPS 500 x Reply #34 - Apr 22^nd, 2013 at 1:24am hell I just read the manual and quote "do not operate above 60deg" so what does this mean for exhaust testing? I've also been road testing with this thing under the bonnet. Has anyone destroyed one yet???
Back to top	can't see, can't hear, can't remember IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,598 Olympia Washington USA Gender:	Re: WPS 500 x Reply #35 - Apr 22^nd, 2013 at 7:55am The 140° F max temp refers to the temperature of the unit itself. Since exhaust does not flow through it during testing, you should be fine. We have not seen any damaged by overheating.
Back to top	Tom Roberts Forums Administrator IP Logged

KarlW LSD Guide Picogroup Offline Picoscope In The Ville Posts: 1,347 Somerville Massachusetts USA Gender:	Re: WPS 500 x Reply #36 - Aug 16^th, 2013 at 12:41pm Tom or Brian, Is there anymore bumper's? I couldn't find them on the home pg.
Back to top	IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,598 Olympia Washington USA Gender:	Re: WPS 500 x Reply #37 - Aug 16^th, 2013 at 1:40pm Karl, Yes we have the WPS bumper caps. You'll find them here: http://www.autonerdz.com/wps500.html Add to cart button just above the photo of the WPS with the caps on.
Back to top	Tom Roberts Forums Administrator IP Logged

KarlW LSD Guide Picogroup Offline Picoscope In The Ville Posts: 1,347 Somerville Massachusetts USA Gender:	Re: WPS 500 x Reply #38 - Aug 16^th, 2013 at 3:15pm Tom Roberts wrote on Aug 16^th, 2013 at 1:40pm: Yes we have the WPS bumper caps. You'll find them here: Nice!! I think its a browser thing again. Thats prob why I couldn't find contest message either This is what I see Thank you too!!
Back to top	Autonerdz_web_sight_wps.jpg (70 KB \| ) IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,598 Olympia Washington USA Gender:	Re: WPS 500 x Reply #39 - Aug 16^th, 2013 at 3:43pm That page looks correct. Now to get to the page I linked to click there on the WPS box. Scroll down to the picture of the WPS sitting on the supercharger. The buy button for the caps is just above that where it says they are now included in our kits.
Back to top	Tom Roberts Forums Administrator IP Logged

KarlW LSD Guide Picogroup Offline Picoscope In The Ville Posts: 1,347 Somerville Massachusetts USA Gender:	Re: WPS 500 x Reply #40 - Aug 16^th, 2013 at 4:38pm Tom Roberts wrote on Aug 16^th, 2013 at 3:43pm: Now to get to the page I linked to click there on the WPS box. OK, I'm a F%^&en Idiot. That was tough
Back to top	IP Logged

nobbyclrk Super Nerd Picogroup Offline Posts: 526 Thursday Island Queensland Australia Gender:	Re: WPS 500 x Reply #41 - Aug 16^th, 2013 at 7:54pm Quote: OK, I'm a F%^&en Idiot Spell check must be still busted.
Back to top	When eating an elephant, it's best done one byte at a time IP Logged

PRESTON LSD Guide Picogroup Offline "Fix like a champion today" Posts: 4,961 Jensen Beach Florida USA Gender:	Re: WPS 500 x Reply #42 - Aug 17^th, 2013 at 2:20pm nobbyclrk wrote on Aug 16^th, 2013 at 7:54pm: Spell check must be still busted. HA HA HA HA LOL Now THAT is funny!
Back to top	Rogue Nerd in South FL WWW IP Logged

Denis_soares Freshman Member Offline I'm an Autonerd Posts: 2 Frutal Brazil	Re: WPS 500 x Reply #43 - Sep 15^th, 2013 at 9:00am Ola, moro no brasil e gostaria de comprar o WPS500.
Back to top	IP Logged

Bevatron Senior Member Picogroup Offline LSD moments to learn a lifetime to master Posts: 212 Maryland Maryland USA Gender:	Re: WPS 500 x Reply #44 - Sep 15^th, 2013 at 10:21am Denis_soares wrote on Sep 15^th, 2013 at 9:00am: la, moro no brasil e gostaria de comprar o WPS500. Translation Hello, I live in Brazil and would like to buy WPS500.
Back to top	Hans IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,598 Olympia Washington USA Gender:	Re: WPS 500 x Reply #45 - Sep 15^th, 2013 at 10:57am Bevatron wrote on Sep 15^th, 2013 at 10:21am: TranslationHello, I live in Brazil and would like to buy WPS500. I would recommend that Denis check to see if his local Pico representative can help with that.
Back to top	Tom Roberts Forums Administrator IP Logged

autosparky Super Nerd Picogroup Offline blind worker Posts: 2,537 Porirua New Zealand Gender:	Re: WPS 500 x Reply #46 - Sep 15^th, 2013 at 11:07pm I used the WPS today on the fuel pressure regulator and I totally forgot about the zoom function, does anyone bother using it or do you let the Pico software do the zooming? What about the preset software? who's using the Autonerdz or the Pico? I use Pico
Back to top	can't see, can't hear, can't remember IP Logged

Anthony Lamb

Super Nerd
Picogroup

Offline

Posts: 1,202

Brisbane
Queensland
Australia
Gender: male

Re: WPS 500 x
Reply #47 - Sep 16^th, 2013 at 2:42am

autosparky wrote on Sep 15^th, 2013 at 11:07pm:

I totally forgot about the zoom function, does anyone bother using it or do you let the Pico software do the zooming?

To be honest I have only tried zooming in the WPS once while playing with it, all the other times I have zoomed in vertically after taking and saving the capture with the picoscope software. Don't think it would matter to much on a fuel pressure regulator diaphragm though.

Just keep in mind once you do zoom in I think you loose the the value of the pressure reading and it works like a first look sensor from what I have read I may be wrong.

autosparky wrote on Sep 15^th, 2013 at 11:07pm:

What about the preset software? who's using the Autonerdz or the Pico? I use Pico

I think I seen some where but cant remember where exactly, where Tom and Brain were saying to stay away from the factory Pico probes for the WPS as it was doing some weird things occasionally. I couldn't tell you if it is still true about the later software builds.

I use the Auto Nerdz presets if that helps.

Back to top

IP Logged

Mick

LSD Guide

Offline

I learn every day

Posts: 7,471

Toronto 400ft
Ontario
Canada
Gender: male

Re: WPS 500 x
Reply #48 - Sep 16^th, 2013 at 7:26am

Anthony Lamb wrote on Sep 16^th, 2013 at 2:42am:

Just keep in mind once you do zoom in I think you loose the the value of the pressure reading and it works like a first look sensor from what I have read I may be wrong.

Your are correct Anthony

Anthony Lamb wrote on Sep 16^th, 2013 at 2:42am:

I use the Auto Nerdz presets if that helps

That's the best advice. Wink

Back to top

Mick

IP Logged

Anthony Lamb Super Nerd Picogroup Offline Posts: 1,202 Brisbane Queensland Australia Gender:	Re: WPS 500 x Reply #49 - Sep 17^th, 2013 at 5:34am Thanks Mick I wasn't 100% sure about the zooming
Back to top	IP Logged

autosparky Super Nerd Picogroup Offline blind worker Posts: 2,537 Porirua New Zealand Gender:	Re: WPS 500 x Reply #50 - Sep 17^th, 2013 at 11:43pm any ideas what goes wrong with the Pico software on the later builds?
Back to top	can't see, can't hear, can't remember IP Logged

Anthony Lamb Super Nerd Picogroup Offline Posts: 1,202 Brisbane Queensland Australia Gender:	Re: WPS 500 x Reply #51 - Sep 18^th, 2013 at 3:58am I think it sometimes very rarely displays some anomalies that aren't actually present and worse with a running compression waves.
Back to top	IP Logged

Tom Roberts

Autonerdz Administrator
Picogroup

Offline

Autonerdz Founder

Posts: 8,598

Olympia
Washington
USA
Gender: male

Re: WPS 500 x
Reply #52 - Sep 18^th, 2013 at 8:21am

autosparky wrote on Sep 17^th, 2013 at 11:43pm:

any ideas what goes wrong with the Pico software on the later builds?

Anthony Lamb wrote on Sep 18^th, 2013 at 3:58am:

I think it sometimes very rarely displays some anomalies that aren't actually present and worse with a running compression waves.

These are discussions best suited for the Picogroup areas of the boards. Obviously we would need specific details for what you are experiencing.

For odd WPS behavior you might want to read this thread:

http://www.autonerdz.com/cgi/yabb2/YaBB.pl?num=1372443520

Back to top

Tom Roberts
Forums Administrator

IP Logged

	Welcome, Guest. Please Login or Register

Autonerdz forums