| The Autonerdz Community Forums | |
|
https://yabb.autonerdz.com/cgi/yabb2//YaBB.pl
>> >> 2008 Yamaha R6S High Speed Misfire/Stumble https://yabb.autonerdz.com/cgi/yabb2//YaBB.pl?num=1487131762 Message started by RedlinePowersports on Feb 14th, 2017 at 8:09pm |
|
|
Title: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 14th, 2017 at 8:09pm
Hey guys,
My name is Russ and I am new to the forum and to the picoscope. Starting to get the hang of it but still have much to learn. I am going to share some waveforms that I collected today, hope you guys can shed some light on what I have found today. We are a small motorcycle dealership and we have a customer with a 2008 Yamaha R6S track bike. It has a high speed misfire/stumble but will only do it when at full engine temp (above 210 degrees) and about 140 MPH. I put a channel "A" on the cam I.D. sensor. (cam position sensor) I do not see any fault with this sensor. I see a regular square wave that is consistent and regular. Channel "B" is on the crank position sensor and I see some variations but not seeing anything thats really jumping out at me. Channel "C" is a 20A amp clamp on the primary wire going to the ignition coils. I have all four on this clamp so that I can see the ignition pulses on all cylinders to see if the stumble is all the cylinders or just one or two. I was able to get it to do a small stumble and I can do my best to point that out on the waveform but I feel like you guys will see it. On my dyno when the stumble gets bad enough I will see a 40hp drop in power. I am anxious to see what you guys think. Pleasure to meet you guys and thanks in advance! :) Wiring diagram attached and I will do my best to drop the waveforms in the dropbox. https://yabb.autonerdz.com/cgi/yabb2//YaBB.pl?action=downloadfile;file=2008_Yamaha_R6S_Wiring_Diagram.oxps (283 KB | ) |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 14th, 2017 at 8:31pm
This waveform I had the stumble late in the screen. Not 100% sure what im looking at. Please let me know if you guys have any tips!
https://yabb.autonerdz.com/cgi/yabb2//YaBB.pl?action=downloadfile;file=__20170214-0003.psdata (19921 KB | ) |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 14th, 2017 at 8:49pm
This waveform I added channel "D" for battery voltage. I wanted to make sure the battery was not being overcharged and sending too much power to the ECU. (I had this very problem on an atv earlier this year that was causing ignition breakup)
I have uploaded this file to the dropbox under Redline Russ folder. Too large to post here. |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 14th, 2017 at 9:01pm
Hi Russ and welcome to the group. Being as you are a Picogroup member you have access to the bottom half where you may get more of a response vs the public area.
Next I took a look at you capture and would like to point out a few things. For those of us that were not present in front of the bike we could use a bit of help with what you have each channel attached to such as but not limited to crank sensor, cam sensor, ignition coil amps, etc., etc. I did notice you put it in your opening post but it would be nice on the capture. In the notes area maybe a little more of what is going on during the capture. Now as far as the capture goes your sample interval is to slow. Do you know how to adjust it? If so 1us would be minimum but I would suggest 500ns due to the speed of the events happening during your capture. If you don't understand then say the word and we'll help you out with it. |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 14th, 2017 at 10:01pm
Spence, thanks for the response. When I get to the shop tomorrow I will take a look but from what I remember I tried to get it to increase the sample rate but for some reason it would not go above 4 micro seconds (4us, correct?) if I am remembering that correctly as it is all very new to me.
Maybe if someone is willing to help get the right settings to capture the event properly that would be great! Is there a way an admin can move this topic to the member area so I dont clutter things by reposting? |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 15th, 2017 at 8:50am
Russ try 500ms/div and top middle most of us start by putting it to 6MS which will give you a 800ns sample rate. It you case I would kick it up a bit higher to 10MS.
I can post screen mark ups later if you don't understand what I am referring to or one of the others might do it or point up to a thread where we discussed this. Look forward to seeing your new captures. Do you know how to get a secondary pattern on this engine? Stay in touch Spence |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Tom Roberts on Feb 15th, 2017 at 9:02am RedlinePowersports wrote on Feb 14th, 2017 at 10:01pm:
Done RedlinePowersports wrote on Feb 14th, 2017 at 10:01pm:
You have requested 5 million samples and that's what you got. Just need to step on the gas a bit more. Not bad though. You appear to have captured the problem. This is CD ignition, so the coil fires on an expanding magnetic field. Hundreds of volts are applied to a grounded primary to make the field expand quickly and induce secondary voltage. What I see late in your capture is that the cylinder after the CID is consistently missing it's primary current spike. I would have to conclude that coil is misfiring. Would be interesting to see secondary with the primary voltage and current to see where spark time is in relation to the other signals. I have converted your oxps file to pdf and attached so more can view it. https://yabb.autonerdz.com/cgi/yabb2//YaBB.pl?action=downloadfile;file=2008_Yamaha_R6S_Wiring_Diagram.pdf (370 KB | ) r65miss.jpg (596 KB | ) |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 15th, 2017 at 9:22am Tom Roberts wrote on Feb 15th, 2017 at 9:02am:
+1 Tom Roberts wrote on Feb 15th, 2017 at 9:02am:
Thanks! |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 15th, 2017 at 11:04am
Wow guys you caught those missing spikes and I never knew that was there...what steps did you do to get the scope to show you that?
Secondly, if they are missing the current spikes that would not be the coils fault...that would be the current signal being sent to the coil correct? This bike does have 3 new coils on cylinders 1-3 and 1 on cylinder 4 that the customer said he recently replaced. |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 15th, 2017 at 11:07am
I may also need some direction on how to get a secondary ignition capture with this being a coil on plug setup. I know I can use the inductive pickup wand but I have been told that's not the best way to go about it.
|
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 15th, 2017 at 11:39am RedlinePowersports wrote on Feb 15th, 2017 at 11:04am:
I would be leaning towards the coil but the secondary would be something I would like to see. I will dig up some pictures of what I have used for COP(coil on plug) secondary captures. Having your hand there at 14,000 rpms can be unnerving at times. Do you have any silver metal tape? |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 15th, 2017 at 12:04pm
You could also swap a coil with that one and see if it follows the coil for a down and dirty way but where's the fun in that? 8-)
|
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 15th, 2017 at 12:32pm
Will do! Yes I do have some tape. I will definitely try that!
Spence wrote on Feb 15th, 2017 at 12:04pm:
Exactly! :D |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Tom Roberts on Feb 15th, 2017 at 1:20pm RedlinePowersports wrote on Feb 15th, 2017 at 11:04am:
Since you said it was late in the screen, I just zoomed in and started scrolling thought that area until I saw something different. [smiley=maglass.gif] |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 15th, 2017 at 2:38pm
Tom, Thanks!
If you guys had not directed me and had not spotted that, I am not sure I would have solved this. It would seem that is a #4 bad coil. It tests fine with a meter. Book calls for 4.8-7.2K ohms and it tests at 7.0k ohms but is missing on the screen as you pointed out. I switched cylinder 4 coil with cylinder 3 and the problem transferred! I would say that proves that the coil that appears to be good with the meter is proven bad with the scope wouldn't you guys agree? I am pretty confident with this diagnosis. I am also confident that this would not have been found without the Pico. :D |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Tom Roberts on Feb 15th, 2017 at 3:05pm RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
That bike is what prompted you go get a Pico eh? Nice maiden voyage for you. It would seem you are onto something here. Please post up the other files when you get a chance. After you moved the coil and that one of secondary with primary voltage and current if you get it. Might be helpful for the next one. Just idle would be fine on that one. Resistance tests of coils are virtually useless. If this had been an inductive discharge ignition system we would have known better what to do and look for but, at least for me, this is an unfamiliar system. |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 16th, 2017 at 7:45pm RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
Dynamic testing is where it's at! RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
Cool! How about showing us that capture. RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
Sure does about 99% [smiley=thumbsup.gif] RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
As well you should be. You pretty much proved it. 8-) RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
You may have found it without it after how many hours of trying an educated guess from the gut. Changing a bunch of parts that may not of been needed... Adjusting a bunch of setting that didn't really need to be adjusted and who knows the wear and tear on the dyno and bike with the tests that came up empty. Add to that all the hours that netted no income and the stress that come with that. And how about the hours of work that didn't get done chasing this issue down... I'd say you made a good investment. Even better was the great idea of where you bought it which put you on here with all us other nut cases! 8-) Glad to hear you got it figured out. Spence |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by RedlinePowersports on Feb 19th, 2017 at 8:50pm
Thanks Spence! I will be working on getting the repaired bike waveforms up here once I get the new coil.
The only reason I didn't post the capture of the coil switched from cyl #4 to cyl #3 was because they look the same but just one cylinder over. On a side note how do I post a waveform screenshot like Tom did earlier in this thread? |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by StitchB on Feb 20th, 2017 at 5:26am RedlinePowersports wrote on Feb 15th, 2017 at 2:38pm:
Ohm testing?, my mother always said, if you don't have anything nice to say, don't day anything. Maybe I already said to much, JMO. |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by StitchB on Feb 20th, 2017 at 5:29am Tom Roberts wrote on Feb 15th, 2017 at 3:05pm:
Redline, your going to love this tool, every bike shop should have one with all the latest Can Bus and stuff, just is a no brainer, but my guess is you will have the only one for miles. StitchB |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Spence on Feb 20th, 2017 at 5:55am RedlinePowersports wrote on Feb 19th, 2017 at 8:50pm:
You're welcome! Looking forward to the after capture as well as the dyno results. 8-) RedlinePowersports wrote on Feb 19th, 2017 at 8:50pm:
And that is just the thing we like to see. This shows your result and helps prove it out. If someone in the future is reading this they can see how you did it and what it looked like. RedlinePowersports wrote on Feb 19th, 2017 at 8:50pm:
There are more then one way to do it. I hit "print screen" on my keyboard then I open "paint". From there paste it in, do what you want to it, save it and then post it. Enjoy your day! Spence |
|
Title: Re: 2008 Yamaha R6S High Speed Misfire/Stumble Post by Tom Roberts on Feb 20th, 2017 at 9:43am RedlinePowersports wrote on Feb 19th, 2017 at 8:50pm:
We all have different ways of doing this. I like to go to Pico Edit/Copy Entire Window as Image. Then I paste that into IrfanView image program and add notes, arrows and such. Save that image as a jpeg and attach it here like anything else. Then it appears at the bottom of the post. More details here: http://www.autonerdz.com/cgi/yabb2/YaBB.pl?num=1330357236 |
|
The Autonerdz Community Forums » Powered by YaBB 2.5 AE! YaBB Forum Software © 2000-2010. All Rights Reserved. |